Service Plans: For Equipment Out Of Warranty

• Heating Equipment
  • Natural Gas Furnace Maintenance
  • Oil Furnace Maintenance
  • Propane Furnace Maintenance
  • Hot Water Heater Maintenance
  • Heat Pump Maintenance
  • Natural Gas Fireplace Maintenance
  • Propane Fireplace Maintenance
  • Boiler Maintenance
  • Geothermal Maintenance
  • Heat Recovery Ventilator Maintenance
• Cooling Equipment
  • Air Conditioner Maintenance
• Cost
• Payment
• Contract Conditions
  • Coverage
  • Renewal
  • Plan Cancellation
  • Moving:
    • Transfer
    • Cancel

• Oil Pump
• Electrode Assembly
• Nozzle & End Cone
• Oil Filter
• Air Filter (1” standard)
• Transformer
• Combustion Chamber
• Primary Control
• Fan Control
• Draft Regulator
• Fan & Motor
• Oil Burner Motor & Fan
• Belt
• Vent Connector

• Replacement Parts Included:
• Thermocouple
• Burners
• Pressure Switch
• Gas Valve
• Air Filter (1” standard)
• Ignition Control
• Hot Surface Ignitor
• Flame Sensor
• DSI Ignitor
• Fan Control
• Limit Control
• Fan & Motor
• Power Pile
• Belt
• Ventor Assembly

• Condenser Fan Motor
• Fan Relay
• Temperature Limit
• Hi Pressure Limit
• Air Filter (1” standard)
• Low Pressure Limit
• Suction Filter
• Compressor Relay
• Fan Blade
• Condenser Fan Housing
• Evaporator Orifice
• Expansion Valves
• Access Valves

• Check operation of thermostat or temperature control
• Check safety controls
• Lubricate fan motor & bearings
• Check blower operation (forced air)
• Check fan belt tension and alignment (forced air)
• Clean out flue passages
• Clean and adjust burners
• Clean pilot/ignition control sensors (gas/propane)
• Replace nozzle (oil)
• Visually check venting system
• Remove debris from chimney base or cleanout
• Check filter and instruct the customer on filter maintenance
• Remove vent and check furnace breach
• Check heat exchanger for cracks or holes
• Efficiency test & report

1. Check operation of thermostat
2. Check safety controls
3. Check return air temperature
4. Check supply air temperature
5. Check cooling temperature
6. Check current/voltage
7. Clean condenser
8. Check electrical connections
9. Check subcooling
10. Lubricate fan motor in furnace
11. Check head pressure
12. Check suction pressure
13. Check for leaks
14. Check & clean condensate lines
15. Check outside ambient temperature
16. Start rotor amps
17. Close bypass dampers
18. Mark air conditioner fuse/breaker

• Thermocouple
• Burners
• Pressure Switch
• Gas Valve
• Air Filter (1” standard)
• Ignition Control
• Hot Surface Ignitor
• Flame Sensor
• DSI Ignitor
• Fan Control
• Limit Control
• Fan & Motor
• Power Pile
• Belt
• Ventor Assembly

1. Service accounts must either be paid on
   1. a cash basis, or
   2. current Bryan’s Fuel account.
2. This service must be paid when invoiced or it can be included in the Equal Payment Plan (EPP).
3. There shall be NO liability under this agreement for: Structural alterations to the premises necessary for service, repair, or replacement included in this agreement. Any default, delay in performance, or extraordinary damage hereunder caused by any contingency beyond our control including, without limitations, war, fire, flood, strike, labour disturbance, accident, acts of God, or Government authority. Consequential damages of any nature whatsoever, either arising because of, or resulting from an equipment component failure or the inspection, maintenance, or repair of said equipment. This agreement does not duplicate the protection provided under any other existing warranty or contract. Poor heating and ventilation system performance due to design conditions. Failure to discover latent or manufacturing defects, internal working conditions of sealed components, or unforeseeable occurrences.
4. The time, means, and methods to be employed by the dealer in the performance of this agreement, and the repair or replacement of defective materials, parts, or units is solely at the dealer’s discretion. This agreement shall be void if the equipment listed on the agreement, in the dealer’s judgment, has been subject to misuse, negligence, accident, fire, flooding, lightning, electrical overload, wind storm, vandalism, or has been tampered with, or operated contrary to the manufacturer’s instructions.
5. This service plan only applies to heating and air conditioning equipment located and operating in the customer’s residence. A service agreement is required for each piece of equipment.
6. Bryan’s Fuel reserves the right to decline this service to any of its customers.
7. Contracts will be automatically renewed on the agreement’s expiry date unless Bryan’s Fuel is notified of the cancellation.
8. The following parts are not included:
   1. Heat Pump Parts
   2. Oil Lines
   3. Low-Water Cutoffs
   4. Heat Exchangers
   5. Smoke Pipes other than to chimney base
   6. Oil Tanks
   7. Electronic Thermostats
   8. Non-System Circulating Pumps
   9. Hydronic Zone Valves
   10. Refrigerant/Freon
   11. Condensate Pump
9. There is a yearly maximum of $800.00 per appliance covered under this plan starting from the date of contract or renewal date. This plan cannot be renewed in the middle of the contract year.

This AGREEMENT is NOT IN EFFECT until payment is made in full and the acceptance is signed and dated by a representative from Bryan’s Fuel.